Altec 1592B repair, 1588B module, XLR pinout output etc

Recently i got a nice Altec 1592B mixer.

Each input requires a dedicated preamp/transformer module, for microphones there’s preamp, 1588B or preamp+12v phantom power, model 1588C.

I had to do a massive recapping job on the 1592B- the original caps values were all over the place-and i mean not only electrolytics-the only ones that were still measuring ok were the tropical fish and some of the lower values disc caps- though most of the electrolytics were good quality, Mallory or West Germany made, ROE (Roederstein). I replaced them all with Elnas (they seem to be the standard nowadays).

Also, the resistor after power transformer 7818 (that feeds part of the tone section, so if you have an unit that powers up but does not produce a sound, check for +18v at pin 6 of the tone board, that is linked to the power board after (out) the aforementioned 7818) was burned-clear sign that some damage had taken place. The schematic calls for a 10 Ohms resistor-i decided to put a 100 ohms substitute, much better.

Sounding good, i decided to recap also the 1588B module i have here (more are on the way, and when factory new, they were fitted with 3 modules).

After using a small screwdriver to pry the enclosure open, i took a look at this interesting blog (check it) for the schematic-i also took the time to sub the carbon comp resistors with metal film and yes-noise went down.

For your reference, here’s the resistors network:

Q1 and Q2 pinout:

Troubleshooting:

If the preamp is not working, check carefully the resistors-they break easily. One immaculate looking (inside and out, the spongy filler still in good soft condition, no leakages on the plastic screen etc) 1588B i have had a resistor broken at its base, and since the components are so squeezed together it was impossible to see it-i decided to test the transistors (thats why i took the q1 and q2 pics above) since everything was looking proper-and there-i spotted the broken resistor! The preamp would still burst in noise if i knocked the mic gently on the capsule, yet it wont amplify it properly. Thats the resistor connected to ground on the white wire-a pain to desolder too.

If you must desolder stuff, be patient-these boards wont take a 300 degrees hot iron-the circuit tracks will lift if you heat them up too much-use care.

Since someone over at the Tape Operator forum has raised the warning that the power supply may have been ill designed, i am powering it using an external psu (using the battery option), 24v dc.

Terminal: from left, my battery (external psu) connections (- and +) and pinout to wire an XLR balanced jack to the output: hot, cold and ground… in the mess between high and low impedance i went with, 600 ohms, good for any mixer or recorder input. PLEASE note 2 and 3 terminals are bridged (connected) at the terminal post. The signal is nice and strong.

I will not mod this unit, i like it as it is. Nice and retro sounding.

Joemeek VC4 Enhancer

Ted Fletcher designed, two independent channels enhancer, so rare even Ted himself had some trouble remembering it (on this forum thread).

Some hq photos of the machine!

At the back of the unit, for both channels we find one input and two outputs.

At the front, pots, LEDs and switches:

Being two indipendent channels, it’s not a surprise finding two identical pcbs inside, although the channel thats closer to the power transformer (channel 2) features a few more components for power filtering (diodes, a transistor and capacitors).

There:

As with all the original, english made Joemeek products, most of the action, guts-wise takes place under the pcb.. there it’s all surface mount components.

Thats channel one, assuming channel two doesnt bear any differences, underside-i suppose all the main differences relate to thepower filtering as stated above..